SGM Studio 12 Podręcznik Użytkownika

Version 2.0

Set the knob as required.To allocate a Chase to a memory Register:A Chase can be run from a memory Register in the section marked REGISTER.1. Put the

STUDIO SC USER GUIDERegisters SectionThe dark gray knobs and the keys and light blue printing identify this section.The Studio desks have two operatin

3. Release the Mode key12 SGM Light Technology 23/08/1999 Ver. 2.00

STUDIO SC USER GUIDETo allocate a scene (preset) to a register:1. Set up the required scene on preset A or B2. Press and hold the Grab button3. Press

To fade in/out a Register in a set time:The Registers can be either AND or OR mode.1. Disable the Register (press the button under the Register fader

STUDIO SC USER GUIDEPatching FunctionsPatching a dimming channel1. Press button Setup2. Use the Up/Down arrows to scroll to Dimmer Patch menu3. Press

Scan Control FunctionsThe gray knobs and keys and light blue printing identify this section.Manual use of the unit:A unit can be manually controlled a

STUDIO SC USER GUIDE4. Set the parameters as necessary5. Press the left-hand scroll button to move back to the unit control channelsTo set up a progra

1. Press the Direct button2. Press the program number and release, the program is now running3. Set the time of the program using Speed and Rate knobs

STUDIO SC USER GUIDE5. To modify the scanning area, press the light gray button under the one of the 4 smallcorner symbols, showed on the display, the

TABLE OF CONTENTS2 SGM Light Technology 23/08/1999 Ver. 2.00

To reset a Unit:1. Press the Util button.2. Scroll with the scroll buttons until “Reset” appears on the display.3. Press the light gray button corresp

STUDIO SC USER GUIDEInternal LibraryThis menu, made up of 3 sections, allows you to create, modify or delete the Fixture’sconfiguration from the Pilot

To insert a new fixture configuration into the Studios’ library:6. Press the Menu button.7. Scroll with the up/down arrows until “Internal Library” ap

STUDIO SC USER GUIDE3b) Effect String: allows to write the parameter’s name on top of each scann controlfader.1. By using the up/down arrows replace t

To set the Hard/Soft Cross:1. Scroll with the up/down arrows until “Hard/Soft Cross” appears on the display.2. Press the right-hand Scroll button to e

STUDIO SC USER GUIDESynchronization of the Desk with MIDI SignalAll the Studio desks can be driven by using an external device, which can provide a MI

Synchronization of the Desk with RS232The Studio can use the serial interface for connection to outboard devices, which synchronize itsoperation. By m

STUDIO SC USER GUIDEConnection of the RS -232 CABLE for Studio lighting consoles: 2 RX TX3 3 TX RX2 7 RTS CTS8 8 CTS R

4. When you want to STOP the recording, hold down the <PLAY> key and press again the track’skey you selected before.28 SGM Light Technology 23/0

STUDIO SC USER GUIDE5. To PLAY-BACK the track, you must hold down <PLAY> key and then press the track’s key youhave just recorded, exactly at th

STUDIO SC USER GUIDETo Clear All the Memory...

To set the Hard/Soft Cross:...

STUDIO SC USER GUIDETo Clear All the Memory1. Switch on the board while holding down the Grab key (located by the memory registerssection)2. 1-10 will

Manual Preset Section6 SGM Light Technology 23/08/1999 Ver. 2.00

STUDIO SC USER GUIDEThe light gray faders, keys and printing, identify this section.There are 12 (STUDIO 12 SC) or 24 channels (STUDIO 24) available a

Flash Function:The flash master must be put to full.If the button underneath a channel is pressed when the flash master is raised then thechannel will

STUDIO SC USER GUIDEChase SectionTo set up a chase:1. Put the Direct fader to full and push the button underneath2. Press and hold down the Chase butt